EMC Engineering | Case Context
An electronic system can operate correctly while its power-input current exhibits significant low-frequency variations. Even when average power consumption remains unchanged, periodic mission loads can introduce frequency components that must be considered in conducted emissions analysis.
01. Same Average Power, Different Load Profiles
02. From Load Demand to Input Current
03. Understanding CE101-Related Emissions
A constant 42 W load and a periodic 30–90 W mission load have the same average power. However, their time-domain behavior and frequency content are fundamentally different.
The power-input response depends on the source impedance, input network, DC/DC converter, control dynamics, and local energy storage. Load-current variations do not necessarily appear unchanged at the equipment input.
Periodic input-current variations can produce low-frequency harmonic components relevant to CE101 evaluation. Identifying their frequencies, amplitudes, and coupling mechanisms is essential before selecting design modifications.






LTSpice Analysis | Engineering Evidence
From Mission Load to Design Decisions
Through a controlled LTspice model, this case study investigates how periodic mission loads affect power-input current, harmonic content, and DC bus stability. Design modifications are evaluated through measurable performance improvements, electrical trade-offs, and clearly defined verification criteria.
01. LTspice Reference Power Model
02. Time & Frequency Analysis
03. Design Interventions & Trade-Offs
A 28 VDC input, nominal 12 V bus, and a behaviorally controlled buck converter establish the reference model. Constant and periodic mission loads are compared using consistent operating conditions and measurement points.
Time-domain waveforms, Fourier calculations, and FFT results reveal mission-related input-current harmonics. Controlled changes in mission frequency help distinguish load-related spectral components from other contributions.
Output capacitance, ESR, input filtering, and damping configurations are evaluated against input-current harmonics, bus-voltage stability, and electrical stress. Improvements are assessed together with their potential side effects.
Key Engineering Finding
A 74% reduction in output-voltage ripple did not reduce the 100 Hz input-current harmonic.
In the LTspice model, increasing output capacitance from 470 µF to 4700 µF reduced peak-to-peak bus ripple from 0.970 V to 0.252 V, while the 100 Hz input-current component remained approximately unchanged.
Improving DC bus stability does not automatically improve conducted emissions.


Free Technical Session
Explore the Engineering Behind CE101
Discover why changes in mission load can affect an electronic system's power-input current and low-frequency conducted emissions. This free technical session introduces the engineering problem, its relevance to MIL-STD-461H CE101, and the systematic approach used to investigate it.
An Introduction to the Case Study
This free 30-minute session provides an overview of the engineering problem, its relevance to CE101, and the topics covered in the complete training program.






On-Demand Specialized Course
Follow a 28 VDC power system through mission-load modeling, time-domain simulation, frequency-domain analysis, design interventions, and verification planning.
Built around a consistent LTspice reference model, the program connects simulation results with practical engineering decisions relevant to MIL-STD-461H CE101.
Detailed lessons: 1.1 Case Definition & Initial Evidence Review • 1.2 Power-Chain Architecture & Observation Points • 1.3 Local Energy Storage & Input Network Interactions • 1.4 Mission Load Profile & Duty-Cycle Derivation • 1.5 Load Current & Constant-Current vs. Constant-Power Modeling • 1.6 LTspice Load Model Setup & Result Verification • 1.7 Time Resolution, Measurement Windows & Current Sign Conventions • 1.8 Model Validity, Technical Decision Record & Next Steps.
Time-Domain Power Behavior
Detailed lessons: 2.1 Reference Power Circuit and Model Setup • 2.2 Switching, Control, and Current Paths • 2.3 Startup and Output Voltage Under Constant Load • 2.4 Mission Load and Output Voltage Variation • 2.5 Mission Load Effects on the Power Input • 2.6 Current Balance, Power, and Energy Checks • 2.7 Measurement Window and Numerical Result Verification • 2.8 Evaluation of Results and Next Steps.
Frequency-Domain Analysis
Detailed lessons: 3.1 Introduction to Frequency Analysis & Current Quantities • 3.2 Fourier Analysis & FFT Scaling for Known Signals • 3.3 Time-Window Selection & Spectral Leakage • 3.4 Hann Window & Main Analysis Configuration • 3.5 Mission and Switching Signatures in Input Current • 3.6 Harmonic Amplitude Calculation & Method Comparison • 3.7 R0–R1 Comparison & dBµA Conversion • 3.8 FFT Numerical Consistency Checks • 3.9 125 Hz Experiment & Mission-Related Frequency Analysis • 3.10 From Frequency-Domain Findings to Design Decisions.
Design Interventions & Trade-Offs
Detailed lessons: 4.1 Target Mitigation Criteria • 4.2 Output Capacitance & High-Frequency ESR Tuning • 4.3 Input Filter Damping Topologies • 4.4 Startup Stability vs. Mass Trade-off Analysis.
Verification Planning & Engineering Decisions
Detailed lessons: 5.1 Verification Test Configurations • 5.2 Multi-Corner Mission Scenarios • 5.3 Correlating Simulation to Chamber Test Data • 5.4 Final Engineering Decision Documentation.
Case Definition & System Boundaries
MODULE 01
MODULE 02
MODULE 03
MODULE 04
MODULE 05
Course Access Packages
Select individual engineering access or organization-wide licensing including verified LTspice models and review templates.
BASIC
PROFESSIONAL
CORPORATE
$290
single seat access
$580
single practitioner seat
$1,750
multi-seat team license
Includes complete recorded video access to all five technical curriculum modules. Ideal for individual engineers studying the theoretical foundation.
All five module video lessons, comprehensive downloadable course notes, and full LTspice schematic decks with parameter sweep scripts.
Everything in Professional plus organization-ready CE101 verification templates, decision logs, team terms, and 1 hour of direct technical consultation.
Course Details & Enrollment
What is the primary difference in packages?
Basic offers video lectures only. Professional adds source files and calculation worksheets. Corporate adds multi-seat rights and engineering consultation.
What do the corporate templates contain?
Standardized aerospace engineering templates for CE101 analysis reports, design review trade-off summaries, and physical-to-simulation decision logs.
How is the technical consultation conducted?
Corporate licenses receive a private 60-minute video session with PreEMC engineering leads to review your program's specific input filter topology.
How is online access delivered?
What technical prerequisites are needed?
Are simulation circuit files included?
Credentials are automatically dispatched upon enrollment with perpetual access to all recorded video lessons and module reference slides.
A fundamental background in electrical engineering and basic familiarity with SPICE netlists and switch-mode power converter topologies.
The Professional and Corporate tiers include fully commented, turnkey LTspice schematic files, symbol libraries, and automated FFT setup scripts.
Advance Your Power Subsystem EMC Qualification
Eliminate qualification surprises before entering the anechoic chamber with evidence-based mission load analysis.


